GE PP945 Manual de usuario

GE AppliancesGeneral Electric CompanyLouisville, Kentucky 4022531-9149Profi le30- and 36-in.CooktopsTechnical Service GuideJanuary 2007GE Consumer &

– 10 –ON/OFFTo turn on a single surface element: Touch the ON/OFF pad, then touchthe (+)/(-) pad.Use the (+)/(-) pad to choose thedesired power settin

– 11 –Using the surface elements.To turn on the warming zone surfaceelement:Touch the warming zone ON/OFFpad, then touch the (+)/(-) pad.Use the (+)/(

– 12 –Operation OverviewDIGITAL CONTROL SYSTEMThe digital control system consists of 3 circuit boards: The touch board (permanently adhered to the cer

– 13 –Component Locator Views(Continued next page)Front View (Model PP945) Glass Top With Permanently Attached Touch BoardRelay Power Supply Module Dr

– 14 –Top View - Glass Top RemovedSingle Surface ElementWarming Zone Surface ElementDual Surface ElementDual Surface ElementTri-Ring Surface ElementDa

– 15 –Cooktop ComponentsWARNING: Before servicing the cooktop, power must be removed from the cooktop by turning the power off at the circuit breaker.

– 16 –Daughter Relay Module (DRM)To replace the DRM:Remove the glass top. (See Glass Top.)Mark and disconnect wiring from the module. 1.2.Note: The mo

– 17 –Insulating BarrierInsulating BarrierRelay Power Supply Module (RPSM)If the RPSM is damaged or defective, it can be accessed by opening the drop

– 18 –Heating Elements The radiant heating element consists of a ribbon-type resistance wire attached to the support insulation with molded ceramic wa

– 19 –Mark the numbers on the bottom of the element next to the tabs.Remove the two ¼-in. hex-head screws and tabs. Install them on the new element in

– 2 –IMPORTANT SAFETY NOTICEThe information in this service guide is intended for use byindividuals possessing adequate backgrounds of electrical,elec

– 20 –Diagnostics and Service InformationComponent Quick Reference TroubleshootingHot Light Stays On - Glass CoolHot Light Inoperative - Glass HotHot

– 21 –Component Ohms Test Location Open Circuit CorrectionLeft Rear 1200W Element*46 ΩRPSM J7-2 Orange/Black to K14 Orange Check Element and wiring. B

– 22 –Model PP 945 Test LocationLeft Rear Element* RPSM J2 to J21-3Left Front Element* RPSM L1 to J21-2Right Front Element* RPSM L1 to J21-4Right Rear

– 23 –Schematics and Wiring Diagrams(Continued next page)Model PP945 - Element 240 VAC Schematic WARNING: Disconnect electrical power before servicing

– 24 –WIRING DIAGRAM MODEL PP945

– 25 –MODEL PP975 - ELEMENT 240 VAC SCHEMATICWARNING: Disconnect electrical power before servicing.Caution: Label all wires prior to disconnection. W

– 26 –WIRING DIAGRAM MODEL PP975

– 27 –WarrantyThis warranty is extended to the original purchaser and any succeeding owner for products purchased forhome use within the USA. If the p

– 3 –Table of ContentsComponent Locator Views ...

– 4 –P P 9 7 5 B M 1 B BBrandP = Profi leFeature PackDesignates Features - the higher the number, the more featuresProduct Color B = BlackS = Bl

– 5 –IntroductionThe new electronic cooktops make an eloquent statement of style, convenience, and kitchen planning fl exibility. The electronic touch

– 6 –Installation The branch circuit load for 1 wall-mounted oven or 1 counter-mounted cooktop is the rating on the nomenclature tag of the appliance.

– 7 –Dimensions and ClearancesThe following MINIMUM clearance dimensions must be maintained.13″ MAX. Depth of uprotectedoverhead cabinets30″ MIN.Clear

– 8 –(Continued next page)Control FeaturesON/OFFON/OFFON/OFF12IN9IN6INON/OFFON/OFFHOT SURFACECONTROLLOCKWARMING ZONEON/OFF12IN9IN6INHOT SURFACECONTRO

– 9 –(Continued next page)Using the surface elements. Your new Profile Cooktop makes an eloquent statement of style, convenience, and kitchen planning