Ge GEFanuc Automation Programmable Control Products T Manual de usuario Pagina 154
- Pagina / 268
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
5
5-27
GFK-1004B
Chapter 5 The Station Manager
NODE Command
The NODE command has the form:
NODE
This command causes the TCP/IP Ethernet Interface sign-on message to be printed out
on the screen. When the TCP/IP Ethernet Interface is executing the Soft Switch Entry
Utility, the reason that the utility was entered is also displayed.
A typical NODE command is shown below:
> node
IC697 PLC Factory LAN Interface
Copyright (c) 1990-1995. All rights reserved.
PROM version 2.00 (xxAx), Software version 2.00 (xxAx)
TCP/IP Ethernet
IP address = 3.16.18.47
MAC address = <<080019010177>> MAC default = <<080019010177>>
EM7A2
OK Command
This command causes the STATUS OK LED to turn ON. It has no effect on the contents
of the exception log.
The OK command has the form:
OK
A typical OK command is shown below:
= ok
Display modified
PING Command
The PING command has the form:
PING <node> [ <cnt> [ <sch> [ <len> ] ] ]
where <node> is the Internet address of the destination.
<cnt> is the number of ICMP echo requests to send to the destination.
<sch> is the number of 10 millisecond intervals to wait for a reply from the
destination, and send the next ICMP echo.
<len> is the length of the ICMP echo message (minimum of 8 bytes).
- GE Fanuc Automation 1
- Warnings, Cautions, and Notes 2
- Content of this Manual 3
- Related Publications 4
- Contents 10
- Chapter 1 Introduction 15
- The Ethernet Interface 16
- The Ethernet Software 18
- The Configuration Editor 19
- The Downloader 19
- How to Make it Work 20
- Quick Guide to the Manual 21
- Board Indicators 24
- Restart Button 24
- C:\> cd \gsm 29
- C:\GSM> gsm 29
- Problems During Power-Up 31
- Configuring a Station 41
- Downloading a Station 42
- Initiating the Download 43
- Problems During the Download 44
- Running Field Network Test 47
- Configuration 53
- What is the GSM? 54
- Hardware Requirements 56
- Setting-Up DOS System Files 60
- Unusual Procedures 64
- Starting-Up the GSM 65
- GSM Keyboard Functions 67
- GSM Menu Structure 68
- Configure a Station Screen 69
- Structure of the MAC Address 72
- TCP/IP Parameters Screen 74
- Advanced Parameters Menu 76
- Data Link Parameters Screen 77
- System Parameters Screen 79
- Download Station Screen 81
- Downloading Over the Network 82
- Access Station Manager Screen 84
- List All Stations Screen 85
- Setup GSM Menu 87
- Set Download Mode Screen 88
- Exit to DOS 88
- COMMREQ Function Block 91
- COMMREQ Command Block 91
- Channel Commands 91
- Status Data 92
- Domain of a channel 93
- Domain of a TCP connection 93
- The COMMREQ Function Block 94
- The COMMREQ Command Block 95
- Section 3: Channel Commands 97
- Establish Read Channel (2003) 99
- GFK-1004B 102
- Example Command Block 103
- A Channel Command 104
- Abort Channel (2001) 109
- Section 4: Status Data 113
- Types of Status Data 113
- Status Bits 114
- Communications Status Words 117
- Table 4-4. Major Error Codes 118
- Minor Error Codes 119
- FT Output is ON 125
- Chapter 5 The Station Manager 128
- Station Manager Mode 129
- Using the Monitor Commands 133
- Using the Modify Commands 134
- Date and Time 135
- Task Identification 136
- Display Data Representation 136
- Byte String Values 137
- IP Address 137
- Soft Switch Entry Utility 138
- Field Network Test Utility 140
- Command Restrictions 141
- Command Input Processing 142
- CHANNEL Command 143
- BPS Command 144
- CHBPS Command 144
- CHDATE Command 144
- CHLTIME Command 145
- CHSOSW Command 145
- NET Load from network 146
- * Default Value 146
- CHTIME Command 147
- CLEAR Command 148
- CLSOSW Command 148
- DATE Command 149
- EXS Command 149
- HELP Command 149
- LOAD Command 151
- LOG Command 151
- LOGIN Command 152
- LOGOUT Command 153
- LTIME Command 153
- NET Command 153
- NODE Command 154
- OK Command 154
- PING Command 154
- PROG Command 155
- REM Command 155
- REPORT Command 156
- REPP Command 157
- RESTART Command 157
- SHOW Command 158
- Configuration Parameters 159
- <<00080000>> 160
- SOSW Command 161
- STAT Command 161
- STOPP Command 162
- STOPT Command 162
- TALLY Command 163
- Tally Meaning 164
- TEST Command 169
- TIME Command 170
- TRACE Command 170
- Chapter 6 Troubleshooting 172
- Using this Chapter 173
- The Power-Up State 176
- The Soft Switch Entry State 176
- The Field Network Test State 177
- The Loader State 178
- The Operational State 179
- Log Event Cause 181
- Chapter 6 Troubleshooting 182
- Log Event 182
- Appendix A Glossary 208
- Glossary of Terms 209
- What this Appendix Contains 216
- Serial Port Settings 216
- Serial Port Pinouts 216
- Serial Cable 217
- Display Terminal Settings 217
- Ethernet AUI Port Pinouts 218
- AUI (Transceiver Cable) 219
- Transceiver Description 219
- Config Mode 221
- Station Address 222
- Network Load Address 223
- Load Source 223
- LAN Online 223
- Backplane Online 223
- Modify Soft Switch Settings 224
- 3Com Etherlink II 229
- 3Com Etherlink 3 230
- 3Com Etherlink 16 231
- 3Com Etherlink /MC 232
- \CONFIG.SYS 233
- \AUTOEXEC.BAT 233
- \GEFNDIS\PROTOCOL.INI 233
- Intel 82593 234
- Xircom Pocket Adapter (PE2) 235
- Xircom Pocket Adapter (PE3) 236
- IBM PCMCIA 238
- Error Code Description 240
- Table E-2. NDIS Error Codes 242
- Appendix F Network Test Form 243
- Network Test Data Sheet 244
- Addresses 245
- Gateways 246
- MAC Addresses 248
Relacionado con productos y manuales para Hardware Ge GEFanuc Automation Programmable Control Products T
Hardware Ge JGBS23BEL Manual de usuario
(2 paginas)
(2 paginas)
Hardware Ge ZBD6905 Manual de usuario
(16 paginas)
(16 paginas)
Hardware Ge ZET1 Manual de usuario
(44 paginas)
(44 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.038 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales